Tube Axial Fans

An inline exhaust fan is best defined as a fan that is mounted inline (inside or connected to ducting) that is used for extraction purposes. An inline fan does not sit directly on the plasterboard or ceiling, instead it is typically located inside the attic or roofspace a little bit further away from the room.

• Reduced Noise As the fan is located further away in the roofspace and not directly above you the noise levels within the room you are extracting from will be less.
• High Power  Inline fans are available in large sizes with very high power motors. Quite often this type of power is simply not available from a standard ceiling mounted or wall mounted extraction fan.
• Length of duct run Inline fans are engineered to work with ducting. This means they will retain a greater percentage of their advertised capacity in comparison to basic extraction fans. This is particularly useful if you have a great distance from the extraction point to the outlet. For example if you want to extract your bathroom to a roof vent and the distance is relatively long (6m or more). This makes the fans useful for other applications such as heat transfer and sub floor ventilation.
• More than one intake point With an inline fan it is possible to create multiple inlet or outlets by using a Y Junction or BTO. This is particularly useful if you have a large room and wish to have 2 intake points, or again for a heat transfer kit that services multiple rooms.

Ventilation in a poultry house supplies fresh air that is essential to sustain life. It also helps reduce the extremes of temperature, humidity and air contamination to tolerable limits for confined chickens.
United make Ventilation Fans removes excess heat, moisture, dust and odours from the building and at the same time, dilutes airborne disease organisms.  Providing proper ventilation to poultry is necessary and can be mastered by any determined and willing poultry grower. It is a challenge, however, since poultry houses are different and ventilation requirements change with time of day, season, temperature, humidity, wind, bird age and density. 

Type of axial fans                 :               Axial/Axial reversible/Contra rotating/Bifurcated/Inline

Capacity       :       250 CMH TO 200000 CMH

Diameter        :               10” to 96”

RPM                :               450 TO 3460

Frequency        :               50 Hz./60 Hz.

Voltage          :               415/400/380/110

Phase          :               3 phase/ I phase

Type of drive                        :               Direct/V-belt/Coupling/Plug type/Engine driven/

MOC                                       :               MS/SS ALL Grade/Aluminum/GI/PP/PP+FRP/PP+PVDF/FRVE/MS + Rubber lined

Coating                                   :               HR coating/Powder coating/Hallar coating/PP/PVDF/PTFE/ETFE/FEP

                                                                Hot dip galvanized/Spray galvanized/

Type of mounting                 :               Flange mounted/Wall mounted /Foot mounted/Roof mounted

Inlet temperature                :               Up to 600 deg C

Motor rating                         :               0.25HP to 500HP

Type of blower fans             :               Backward curve/backward straight/Radial straight/open type/Peddle type

Aerofoil /Forward curve/

Type of axial fans                 :               Axial/Axial reversible/Contra rotating/Inline

Capacity                                 :               250 CMH TO 200000 CMH

Diameter                               :               10” to 96”

RPM                                        :               450 TO 3400

Frequency                             :               50 Hz./60 Hz.

Voltage                                   :               110/380/400/415

Phase                                     :               3 phase/ I phase

Type of drive                        :               Direct/V-belt/Coupling/Plug type

MOC                                       :               MS/SS ALL Grade/Aluminum/GI/PP/PP+FRP/PP+PVDF/FRVE/MS + Rubber lined

Coating           :           HR coating/Powder coating/Hallar coating/PP/PVDF/PTFE/ETFE/FEP

                        :          Hot dip galvanized/Spray galvanized/

Type of mounting               :              Flange mounted/Wall mounted /Foot mounted/Roof mounted

Inlet temperatu         :       Up to 600 deg C

Motor rating               :     0.25HP to 500HP

Type of axial fans                 :               Axial/Axial reversible/Contra rotating/Bifurcated/Inline

Capacity          :               250 CMH TO 200000 CMH

Diameter        :               10” to 96”

RPM        :               450 TO 3460

Frequency        :               50 Hz./60 Hz.

Voltage          :               415/400/380/110

Phase        :               3 phase/ I phase

Type of drive          :               Direct/V-belt/Coupling/Plug type/Engine driven/

MOC             :               MS/SS ALL Grade/Aluminum/GI/PP/PP+FRP/PP+PVDF/FRVE/MS + Rubber lined

Coating                                   :               HR coating/Powder coating/Hallar coating/PP/PVDF/PTFE/ETFE/FEP

                                                                Hot dip galvanized/Spray galvanized/

Type of mounting                 :               Flange mounted/Wall mounted /Foot mounted/Roof mounted

Inlet temperature                :               Up to 600 deg C

Motor rating                         :               0.25HP to 500HP

Type of axial fans                 :               Axial/Axial reversible/Contra rotating/Bifurcated/Inline

Capacity    :               250 CMH TO 200000 CMH

Diameter      :               10” to 96”

RPM        :               450 TO 3460

Frequency          :               50 Hz./60 Hz.

Voltage           :               415/400/380/110

Phase            :         3 phase/ I phase

Type of drive         :               Direct/V-belt/Coupling/Plug type/Engine driven/

MOC          :               MS/SS ALL Grade/Aluminum/GI/PP/PP+FRP/PP+PVDF/FRVE/MS + Rubber lined

Coating                                   :               HR coating/Powder coating/Hallar coating/PP/PVDF/PTFE/ETFE/FEP

                                                                Hot dip galvanized/Spray galvanized/

Type of mounting                 :               Flange mounted/Wall mounted /Foot mounted/Roof mounted

Inlet temperature                :               Up to 600 deg C

Motor rating                         :               0.25HP to 500HP

Type of blower fans             :               Backward curve/backward straight/Radial/Radial straight/open type/Peddle type

Aerofoil /Forward curve

Capacity                                 :               5000 CMH TO 300000 CMH

Pressure                                                :               25 mm to 500 mm wg

Diameter                               :               10” to 96”

RPM                                        :               450 TO 2880

Frequency                             :               50 Hz./60 Hz.

Voltage                                   :               415/380/400/110

Phase                                :               3 phase/ I phase

Type of drive                    :             Direct/V-belt/Coupling/Plug type/Engine driven

MOC                :               MS/SS ALL Grade/Aluminum/GI/PP/PP+FRP/PP+PVDF/FRVE/MS + Rubber lined

Coating            :          HR coating/Powder coating/Hallar coating/PP/PVDF/PTFE/ETFE/FEP

                          :           Hot dip galvanized/Spray galvanized

Type of mounting              :             Floor mounted

Inlet temperature              :             40 deg to 600

Outlet temperature           :             250 deg to 300 deg

Motor rating                       :             0.25HP to 300HP